SAFE Systems, Inc.  Abrasive Blasting Equipment Manufacturer
Follow Us
  • Home
  • Products
    • Blast Facility
    • Blast Vessels
    • Dust Collectors
    • Portable Equipment
    • Blast Lights
    • Deadman Switches
    • Enduroguard Cable
  • Parts
    • All Parts
    • Blast Facility Parts >
      • Floor Recovery Systems
      • Bucket Elevator
      • Air Wash Separator
      • Storage Hopper
    • Blast Vessel Parts
    • Dust Collector Parts
    • Portable Equipment Parts >
      • Blast and Recovery Systems
      • Blast Vessel, Trailer Mounted
      • Vacuums
      • Compressed Air Induction (Jet) Vacuum
      • Auto Dumps
      • Vacuum Hose, Vacuum Hose Connectors, Drum Covers
      • Liquid Ring Vacuum (ARS-750 , ARS-1100) Parts
      • Compressed Air Dryer (Deliquescent Style)
  • Support
    • Operation Manuals
    • Product Illustrations
    • How-To Instructions
    • How-To Videos
    • Current Customer Project Status Viewing
  • About Us
    • Management
    • Advanced Engineering
    • Social Responsibility
    • Clients
    • FAQ
    • News and Events
  • Contact Us

Model DC 7100E                                                                   To Dust Collectors >


Specs

Length
Width
Height


Height


Weight


Horsepower
Voltage

Full load Amps


9’-8”
8’-0”
8’-10½” (Shipping position)
12’-3¼” (Working position)
5,500 lbs. (completely empty of dust)
25
460 VAC, 3 phase
28.05

7100E Electric Powered, Skid Mounted, 7100CFM Dust Collector

This compact, portable dust collector has extendable legs that raise the unit to accommodate a 55 gallon drum or other collection device under the dust hopper and then adjust to allow low profile shipping. A direct driven 25 HP motor powers the 7100 CFM exhaust fan. Control of the airflow through the dust collector is managed by an inlet damper. A large, container-style door makes filter access easy.

Versatility is built into this SAFE Systems machine. With one (1) 18” duct inlet on each side of the machine, you can work from either side of this skid-mounted unit. Fork lift pockets and certified crane lifting eyes allow the contractor to easily place it in the most advantageous location.

Nine (9) MERV 11 rated cartridge-type filters collect the dust particles. An electronically controlled, reverse pulse jet of 90 PSIG compressed air systematically cleans the filters, one row of three (3) filters at a time, to dislodge the dust particles which then fall into the hopper below. The dust hopper is equipped with a slide gate for quick dumping of the dust.

A NEMA 4 dust and water tight control box, protects the electrical controls from contaminants and moisture. The unit comes with 25’ of the properly sized SO cord to assist in electrical connection at the job site. Access to the filters and dust hopper, when necessary, is through one large, easy to open and close “Container Style” door.
Picture
Click on Image to Enlarge >

Features:
  •  Skid mounted. 
  •  Extendable legs. 
  •  Forklift pockets. 
  •  Certified lifting eyes for handling by overhead crane. 
  •  Fan and dust collector rated for 7,100 CFM @ 15½” W.C. 
  •  Two (2) dust inlets, 18” diameter (only 1 to be used at a time). 
  •  Automatic reverse pulse cleaning system for filters. 
  •  ¾” air piping for pulse cleaning system. 
  •  Air requirements for pulse cleaning system, 30 CFM @ 90 to 100 PSIG. 
  •  Fan is direct driven by a 25 HP, 460-volt, 3-phase electric motor. 
  •  460 volt AC control box. 
  •  Nine (9) cartridge filters, part # 1000 0300. 
  •  Adjustable inlet damper on the fan inlet for regulating the airflow. 
  •  Slide Gate on the hopper dust discharge. 
  •  Dust discharges onto standard 55 gallon drum (drum supplied by customer) 
  •  25’ of properly sized SO cord for electrical hook-up. 
Notes:
  1. Not intended to be shipped with any dust in collection hopper. 
  2. Recommend emptying dust every 2 to 4 hours depending on collection rate. 
  3. It is recommended that a qualified electrician connect equipment to power and check motor rotation. 
  4. It is recommended that all new filters be coated with precoat dust prior to putting into service.
  5. If operating this equipment using a generator, check with the generator provider to ensure proper sizing.
  6. We recommend at least a 56 KW generator for this piece of equipment.
  7. We recommend shipping this piece of equipment on an open flat bed truck or trailer.
  8. Shipping in an enclosed box van or trailer is not recommended.
Copyright 2023 • SAFE Systems, Inc.  |  Site Map  |  Volatile Metals Market Disclaimer  |  Terms and Conditions | (425) 251 8662 | [email protected]